Double Glazing Door Lock Repairs
Are your uPVC window or door mechanism not working properly? Perhaps the handles on your uPVC windows or doors aren't aligned correctly or are difficult to operate.
You'll be wasting energy when your double-glazed doors do not work properly. This also increases the risk of burglary. Owen the Locksmith can repair your door lock at a reasonable price.
Snapped Key
It can be frustrating when a key gets stuck into the lock. It's also potentially a security risk, as the door might not lock and leave you vulnerable to intruders. There are a few quick fixes you can try to fix the problem and make your door work again.
Remember to remain calm. If you panic and start poking around wildly you could end up pushing the broken piece of the key further into the lock, thereby making the situation much worse.
Spray WD-40, or another penetrating lubricant into the lock. This will help the broken piece come out more easily. You can also use a screwdriver to help break up any pieces stuck that could be blocking the way. If you happen to have a bit of the key visible and you want to remove it, make use of a paperclip, or any other metal object that is thin to grab it and remove it. Both methods work, but be careful not to push the damaged key piece further into the keyway.
Some paperclips have grooved edges that could serve to extract hooks, and some jigsaw blades are also suitable for this use. If you do not have any of these handy, you can use needle-nose pliers to bend and create hooks. Finally, you can make use of a pair of tweezers to grasp and pull out the last bit of the broken keys.
If you are unable remove the broken piece of key Use a lock deicer. It's available in many hardware stores and works by freezing any moisture present in the lock.
If none of these tricks are working, it might be time to call in locksmith. The experts at Fitlocks can quickly fix problems such as broken handles or broken keys with uPVC locks and door mechanisms. They can also reconfigure the double glazing door mechanisms to ensure that they are simpler to use. You can request repairs to your double-glazing online or call us to discuss your requirements.
Broken Cylinder
A damaged cylinder could pose a serious security risk. Luckily, it's an easy repair for professional locksmiths to complete. To fix the cylinder, locksmiths must tap it. They can do this with an hammer or another tool, but the best way is to make use of a long match or piece of wire. Then, position the match's tip or wire near the keyway. After this, the locksmith will strike the lock to crack it open. This is far better than using a heavy hammer that can damage the lock.
The most frequent cause for cracks in the cylinder head is overheating. This can occur when the block and the cylinder head are made of various metals such as cast-iron and aluminum. Different metals can be heated and cool at different rates. This can cause localised hotspots to expand more quickly than the rest of the cylinder.
Another possible cause for cylinder cracks is corrosion. If double glazing repairs near me and the block of the cylinder are not properly maintained, it can result in corrosion or rust, which may cause them to expand at a more than they ought to. As time passes, this may also lead to cracks.
If your uPVC window or door lock is rigid and requires more pressure to turn, it could be due to a variety of causes. A malfunctioning locking mechanism, misalignment or a worn handle are common causes of this problem.
It is a quick and inexpensive fix that most homeowners with double glazing can perform. A professional locksmith should be able solve this problem within an hour of arriving at your property. Depending on your needs, they can replace the locking mechanism, change the window handles, and change the gearboxes. A skilled locksmith will always be able to advise you of the most cost-effective solution for your home. They can also suggest upgrades to the highest-security 3 Star TS007 euro cylinders that will add an extra layer of protection against burglars. It's a small amount to enjoy the peace of mind that comes from knowing your uPVC door is secured.
Broken Handle
Window handle locks have intricate mechanisms that become less effective with time and use, so it's no surprise that they can break. It isn't always easy to pinpoint the reason behind a broken window handle lock and fix it correctly.
The issue could be related to the locking mechanism inside or the latch, fixing the broken handle will improve your uPVC double glazing door's security as well as help you to stop draughts. It can be expensive to repair or replace the handle in a way that isn't done correctly. It can also harm the frame and lock of your door.
Screwdriver When the window is open and the screw loose, loosen the handle. The screw should be on the inside of the backplate, usually concealed by the cap of the screw to enhance the appearance. Be careful not to lose any of the internal parts within the handle, like the plates or levers that are on either side of the spindle. Keep them in the same order so that it is easier to replace them if needed.
Next, turn the handle until it's 90 degrees towards the window frame. Then, loosen the screw at the back of the handle which holds it to the internal spindle using a second screwdriver. Once the screw is removed, you should be in a position to pull the handle off and take off the damaged spindle. Replace it with a new spindle, making sure it's the same length (you can buy them on the internet or at hardware stores). Screw it in place. Don't over tighten the screw as this could harm the handle as well as the window frame.
Check that the new handle is correctly installed, then close and test the handle. It should operate smoothly and you'll be able to open your window once more.
Make sure to check that your uPVC window is shut properly when you're using the handle. If they're not closing properly, you may experience draughts or damp in your home. Also, you could be compromising the energy efficiency of your home. A local window company, like Core Sash Windows, will be able to adjust the hinges on your window frames so they shut correctly.
Broken Spindle
It is often the case that the spindle within the handle is broken, not the handle itself. This is especially typical in uPVC tilt and turn windows. These kinds of windows require a handle which is a lock mechanism that is located in the frame of the window. The handle is connected to a central rod that activates a series of locks that are shaped like mushrooms and secure the window frame keep. If the dead latch mechanism is not able to open when the handle is turned it is likely that the spindle is broken, this can be a frustrating problem.
There are solutions to this issue. A skilled locksmith can quickly and efficiently fix this problem. A reputable locksmith can disassemble the window's handle using a tool that removes the wheel from the area that houses the spindle. This can be done without causing any damage to the handle or causing any other damage to the window frame.
After the wheel has been removed the technician can then examine the spindle to determine what has caused it to break. This involves breaking the spindle into its constituent parts and meticulously noting their general condition as well as any specific areas of wear or damage. This process is typically done in a clean environment by highly skilled technicians.
Next, clean the damaged spindle. This will help remove any dirt or debris which could be hindering it from working normally. After that the spindle is cleaned, it can be repaired or replaced. If the technician is replacing the spindle it is possible to use a dowel that is comparable in size to the original. The technician will then drill matching holes into both pieces. This will ensure that the new spindle is a precise fit with the handle.
If the spindle that is damaged is beyond repair, it could be required to replace it completely. Home centers sell generic replacements. However, if the style of your window is unusual then it will be necessary to speak with a woodworker or cabinet maker who can replicate the exact component for you. After the spindle is installed, it can be fixed to the handle. Place the screw holes on the handle with the screws that are already in the frame. Once the new handle is firmly installed, you are now ready to operate your uPVC window.